Plumbing 101: What You Must Have for Installing a Bathtub
Plumbing 101: What You Must Have for Installing a Bathtub
Blog Article
Presented here in the next paragraph you will find more good quality insights in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a bath tub isn't specifically rocket science, however it does need solid plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bath tub with a new one is also a reasonably difficult job. If the old bathtub is conveniently accessible, the job can relocate speedily; if you need to open up a wall to get rid of the old tub as well as place the brand-new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require an assistant to move out the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the work and also fit attempting it. Rather than working with a specialist to take over a halfway-completed job, it is far better to think about using one before you begin. Opportunities are you might need an expert plumber to make tube links.
This article will assist you mount a new bath tub in your bathroom if you have currently acquired a brand-new bathtub and don't need to change the setup of your previous water supply pipelines.
Your tools and also material list need to comprise the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The procedure of removing the existing faucets can be fairly problematic because of the restricted gain access to that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before carrying on to fit the brand-new taps, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washers remain in place between the faucet as well as the sink. Safeguard the tap in place with the supplier offered backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap adapters. The previous type should be linked to the tap ends first, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Making use of both wood boards under its feet, place the tub in the required setting. The wood boards are handy in evenly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bath tub till the level reads degree.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the suitable supply pipeline by making a compression join; after that do the exact same for the various other tap.
Turn on the water system and also check all joints as well as brand-new pipework for leaks and tighten them if required. Load the bath tub and likewise examine the overflow electrical outlet and the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bathtub needs to wait till the bathtub has been used at least when as this will settle it into its last position.
Planning for the Installment
Firstly, the supporting framework provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the adaptable tap ports to the bottom of the two taps making use of 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be fitted in its final setting.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split an inflexible seal, creating the water to pass through the wall surface in between the bath and the tiling, resulting in problems with wetness as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are marketed in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water prior to securing, to enable the motion experienced when the bathtub is in use. The sealant can crack fairly very early if you do not consider this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally quickly offered on the marketplace. It is recommended to fit the tiles using waterproof or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that post about How to Install a Bathtub when doing a search on the search engines. Enjoyed our piece? Please share it. Let someone else discover it. Bless you for your time. Don't hesitate to pay a visit to our website back soon.
Visit The Following Page Report this page